Postat: 3 maj 2006, 18:01
av karl
som rubriken lyder vad är vtec?? <!--emo&:hmm:-->[img]style_emoticons/<#EMO_DIR#>/hmm.gif[/img]<!--endemo-->
Postat: 3 maj 2006, 22:41
av Auner
VTEC är små hamstrar som när motorn kommer upp i varv springer i sina små hjul och gör att motorn går jetefårt!
Postat: 4 maj 2006, 09:17
av Andreas79
VTEC
From Wikipedia, the free encyclopedia
Jump to: navigation, search
VTEC (standing for Variable valve Timing and lift Electronic Control) is a system developed by Honda to improve the combustion efficiency of its internal combustion engines throughout the RPM range. This was the first system of its kind and eventually led to different types of variable valve timing and lift control systems that were later designed by other manufacturers (VVT-i from Toyota, VANOS from BMW, and so on).
Introduction to VTEC
In the regular four-stroke automobile engine, the intake and exhaust valves are actuated by lobes on a camshaft. The shape of the lobes determines the timing, lift and duration of each valve. Timing refers to when a valve is opened or closed with respect to the combustion cycle. Lift refers to how much the valve is opened. Duration refers to how long the valve is kept open. Due to the behavior of the gases (air and fuel mixture) before and after combustion, which have physical limitations on their flow, as well as their interaction with the ignition spark, the optimal valve timing, lift and duration settings under low RPM engine operations are very different from those under high RPM. Optimal low RPM valve timing, lift and duration settings would result in insufficient fuel and air at high RPM, thus greatly limiting engine power output. Conversely, optimal high RPM valve timing, lift and duration settings would result in very rough low RPM operation and difficult idling. The ideal engine would have fully variable valve timing, lift and duration, in which the valves would always open at exactly the right point, lift high enough & stay open just the right amount of time for the engine speed in use.
In practice, a fully variable valve timing engine is difficult to design and implement. Attempts have been made, using solenoids to control valves instead of the typical springs-and-cams setup, however these designs have not made it into production automobiles as they are very complicated and costly.
The opposite approach to variable timing is to produce a camshaft which is better suited to high RPM operation. This approach means that the vehicle (think: older high performance American cars such as Camaros, Mustangs which idle loudly at stoplights) will run very poorly at low rpm (where most automobiles spend the majority of their time) and much better at high RPM. VTEC is the result of an effort to marry high RPM performance with low RPM stability.
Additionally, Japan has a tax on engine displacement, requiring Japanese auto manufacturers to make higher-performing engines with lower displacement. In cars such as the Supra and 300ZX, this was accomplished with a turbocharger. In the case of the RX-7, a wankel engine was used. VTEC serves as yet another method to derive very high specific output from lower displacement motors.
DOHC VTEC
Honda's VTEC system is a simple method of endowing the engine with multiple camshaft profiles optimized for low and high RPM operations. Instead of one cam lobe actuating each valve, there are two - one optimized for low RPM stability & fuel efficiency, with the other designed to maximize high RPM power output. Switching between the two cam lobes is determined by engine oil pressure. As engine RPM increases, a locking pin is pushed by oil pressure to bind the high RPM cam follower for operation. From this point on, the valve opens and closes according to the high-speed profile, which opens the valve further and for a longer time.
The VTEC system was originally introduced as a DOHC system in the 1989 Honda Integra sold in Japan, which used a 160 hp (119 kW) variant of the B16A engine. The US market saw the first VTEC system with the introduction of the 1990 Acura NSX, which used a DOHC V6. The DOHC VTEC system has high and low RPM cam lobe profiles on both the intake and exhaust valve camshafts. In contrast to the SOHC implementation which switches between cam profiles seamlessly, the DOHC VTEC configuration has a pronouncedly different exhaust note when the switch is made.
SOHC VTEC
As popularity and marketing value of the VTEC system grew, Honda applied the system to SOHC engines, which shares a common camshaft for both intake and exhaust valves. The trade-off is that SOHC engines only benefit from the VTEC mechanism on the intake valves. This is because in the SOHC engine, the spark plugs need to be inserted at an angle to clear the camshaft, and in the SOHC motor, the spark plug tubes are situated between the two exhaust valves, making VTEC on the exhaust impossible.
SOHC VTEC-E
Honda's next version of VTEC, VTEC-E, was used in a slightly different way; instead of optimising performance at high RPMs, it was used to increase efficiency at low RPMs. At low RPMs, only one of the two intake valves is allowed to open, increasing the fuel/air atomization in the cylinder and thus allowing a leaner mixture to be used. As the engine's speed increases, both valves are needed to supply sufficient mixture. A sliding pin, as in the regular VTEC, is used to connect both valves together and allows opening of the second valve.
3-Stage VTEC
Honda also introduced a 3-stage VTEC system in select markets, which combines the features of both SOHC VTEC and SOHC VTEC-E. At low speeds, only one intake valve is used. At medium speeds, two are used. At high speeds, the engine switches to a high-speed cam profile as in regular VTEC. Thus, both low-speed economy and high-speed efficiency and power are improved.
i-VTEC
i-VTEC introduced continuously variable camshaft phasing on the intake cam of DOHC VTEC engines. The technology first appeared on Honda's K-series four cylinder engine family in 2002. Valve lift and duration are still limited to distinct low and high rpm profiles, but the intake camshaft is now capable of advancing between 25 and 50 degrees (depending upon engine configuration) during operation. Phase changes are implemented by a computer controlled, oil driven adjustable cam gear. Phasing is determined by a combination of engine load and rpm, ranging from fully retarded at idle to maximum advance at full throttle and low rpms. The effect is further optimization of torque output, especially at low and midrange RPMs.
In 2004, Honda introduced an i-VTEC V6 (an update of the venerable J-series), but in this case, i-VTEC had nothing to do with cam phasing. Instead, i-VTEC referred to Honda's cylinder deactivation technology which closes the valves on one bank of (3) cylinders during light load and low speed (below 80 mph) operation. The technology was originally introduced to the US on the Honda Odyssey, and can now be found on the Honda Accord Hybrid and the 2006 Honda Pilot. An additional version of i-VTEC was introduced on the 2006 Honda Civic's R-series four cylinder engine. This implementation uses very small valve lifts at low rpm and light loads, in combination with large throttle openings (modulated by a drive-by-wire throttle system), to improve fuel economy by reducing pumping losses.
With the continued introduction of vastly different i-VTEC systems, one may assume that the term is now a catch all for creative valve control technologies from Honda.
Turbocharged VTEC
For 2007 models, Honda's Acura luxury division announced the RDX crossover SUV which will feature a new turbocharged 2.3 litre inline 4 cylinder i-VTEC engine. While Honda has worked with turbo engines for race applications (most notably in Formula 1 during the 1980's Turbo Era) this is one of only a handful of times Honda has applied turbocharging to a road car engine (previous examples incldue the Honda City Turbo and City Turbo II) and the first time to an engine with i-VTEC.
VTEC in motorcycles
Apart from the Japanese market-only Honda CB400 Super Four Hyper VTEC, introduced in 1999, the first worldwide implementation of VTEC technology in a motorcycle occurred with the introduction of Honda's VFR800 sportbike in 2002. Similar to the SOHC VTEC-E style, one intake valve remains closed until a threshold of 7000 rpm is reached, then the second valve is opened by an oil-pressure actuated pin. The dwell of the valves remains unchanged, as in the automobile VTEC-E, and little extra power is produced but with a smoothing-out of the torque curve. Critics maintain that VTEC adds little to the VFR experience while increasing the engine's complexity. Drivability is a concern for some who are wary of the fact that the VTEC may activate in the middle of an aggressive corner, upsetting the stability and throttle response of the bike.
The VTEC experience
Driving vehicles with a VTEC engine that targets performance-minded consumers is a rush for the driving enthusiast. For example, the Honda (Civic CR-X) del Sol VTEC car -- with the B16A DOHC VTEC engine -- is hailed as one of the most fun cars to drive by those who have owned one. In these cars, the driver and passenger are aware when the VTEC "kicks in" due to the sudden increased rushing sound of air being "sucked up" by the intake. While this experience is exciting to those who enjoy driving hard, it isn't for everyone.
Driving a vehicle with VTEC often requires significant additional driver input to operate at very high power outputs. In particular, the Honda S2000 has received complaints from both owners and detractors due to its very high (9,000 rpm) redline in the early models. While the engine produces very high output (120hp per litre), some see the continual need to "row the gears" as a distraction from driving. For contrast, another approach at making high power output is to increase the displacement of a given engine (the 7 litre LS7 motor being an extreme example). Increasing displacement generally harms engine efficiency, but dramatically improves engine output.
Further argument against VTEC is that it is primarily used to control emissions. While there can be no argument that VTEC motors produce substantially higher output, it is true that Honda seems to apply the VTEC label to many engines, some of which are simply "cleaner."
Leecao more info about Vtec:
VTEC is an acronym for Variable valve Timing and lift Electronic Control. It is a mechanism for optimizing air/fuel mixture flow through the engine.
An internal combustion engine converts the chemical energy stored in fuel into thermal energy. The increased thermal energy within a cylinder causes the pressure to build. This pressure acts on the pistons and the result is a mechanical force rotating the crankshaft. This mechanical force is measured as crank torque. The ability for the engine to sustain a certain level of crank torque at a certain RPM is measured as Power. Power is the rate at which the engine can do work. This conversion process is not 100% efficient. In fact, only about 30% of the energy stored in the fuel is actually converted into mechanical energy.
Physics says that for a given efficiency level, a higher rate of fuel consumption is needed for the engine to generate power. So it becomes obvious that if you want more power, you need to increase the rate of fuel combustion. One way to achive this goal is to have a bigger engine. A bigger engine with larger cylinders will be able to combust more fuel per rotation than a smaller engine. Another method is to pre-presurize the fuel/air mixture and cram it into an existing engine size. Thus even though the cylinder size stays the same, more fuel is combusted per rotation. This second method is referred to as forced induction.
Honda chose to explore another method: keep the engine size the same, but turn the engine faster to consume more fuel. Here is an analogy: You want to move foam peanuts from one bucket to another with a cup. You can increase the size of your cup, compress/cram as much peanuts as possible into the cup each time, or you can just move the cup faster. All three methods moves more peanuts. Honda uses the last method. And again, more fuel combusted equals more power generated by the engine.
As the engine speed is increased, more air/fuel mixture needs to be "inhaled" and "exhaled" by the engine. Thus to sustain high engine speeds, the intake and exhaust valves needs to open nice and wide. Otherwise you have what is akin to athsma: can't get enough air/fuel due to restrictions.
If high speed operation is all we have to worry about, Honda wouldn't need to implement VTEC. Indeed, race engines that operate mostly at high rpms do not utilize any mechanism like VTEC. But street cars used for daily driving spend most of their time with the engine at low RPMs. Valves that open wide for high RPM operation contributes to rough operation and poor fuel economy at low RPMs. These undesirable traits are directly against Honda's design goals.
The solution that Honda came up with is the VTEC mechanism: open the valves nice and wide at high RPMs, but open them not as much at low RPMs. So now you have a engine with smooth operation at low RPMs, and high power output at high RPMs.
And that is basically what VTEC is. It's nothing magical. The idea has been around for a long time. Honda's VTEC is just a very simple, elegant and efficient implementation that is extremely effective at achiving its design goal. Honda automobiles are the first among modern automobiles to utilize this mechanism in such a large scale of distribution.
Postat: 4 maj 2006, 19:04
av Mattias I
överkurs kanske?
Postat: 4 maj 2006, 22:20
av Andreas79
<!--QuoteBegin-wain3+4 May 2006, 18:04:36--><div class='quotetop'>QUOTE(wain3 4 4 May 2006, 18:04:36)</div><div class='quotemain'><!--QuoteEBegin-->överkurs kanske?
[right][snapback]279500[/snapback][/right]
<!--QuoteEnd--></div><!--QuoteEEnd-->
Bättre än inget <!--emo&:)-->[img]style_emoticons/<#EMO_DIR#>/smile.gif[/img]<!--endemo-->
Postat: 4 maj 2006, 22:21
av micke_011
hehe.. frågan var ju ställd så ett fullödigt svar är väl på sin plats? mycket text blir'e..
Postat: 5 maj 2006, 09:17
av Andreas79
Är man bra på engelska och vill veta om olika VTEC
såsom både SOCH Vtec och DOHC Vtec o.s.v så är den texten
utförlig och bra ovan jag postade tycker jag iallafall..
Kanske någon annan kan förklara enklare ? <!--emo&;)-->[img]style_emoticons/<#EMO_DIR#>/wink.gif[/img]<!--endemo-->
Postat: 5 maj 2006, 10:52
av tantgron
"Vad är VTEC?" är ungefär som att fråga "Vad är matrix?", eller "Mamma var är saxen?". Det är en kraft som finns där men som ingen vågar utforska med risk för att störa den. Denna mytomspunna energikick (Teh Force) visar vägen för de goda, medan den föraktas av den mörka sidan. Läs även denna tråd "<a href='
http://www.hondaklubben.com/forum/index ... ntry186689' target='_blank'>"Hur låter en CTR motor?" - att uttrycka sig i VTEC</a>"
<!--QuoteBegin-christer_carlsson+10 Sep 2005, 22:43:01--><div class='quotetop'>QUOTE(christer_carlsson 4 10 Sep 2005, 22:43:01)</div><div class='quotemain'><!--QuoteEBegin--><!--QuoteBegin-tantgron+10 Sep 2005, 20:35:17--><div class='quotetop'>QUOTE(tantgron 4 10 Sep 2005, 20:35:17)</div><div class='quotemain'><!--QuoteEBegin-->Hahaaha, det hör kan bli bra! <!--emo&:D-->[img]style_emoticons/<#EMO_DIR#>/biggrin.gif[/img]<!--endemo-->
Voooooooooouuuuuuuaaaa-fffrraaa-vaaaaaiiiiiiiiiiiii!!! <!--emo&:drive1:-->[img]style_emoticons/<#EMO_DIR#>/drive1.gif[/img]<!--endemo-->
(Lägg märke till det metalliska ljudet som V2:n ger ifrån sig när VTEC:en kickar i!) <!--emo&:D-->[img]style_emoticons/<#EMO_DIR#>/biggrin.gif[/img]<!--endemo-->:D [right][snapback]186685[/snapback][/right]
<!--QuoteEnd--></div><!--QuoteEEnd-->Ja, jösses.... <!--emo&:D-->[img]style_emoticons/<#EMO_DIR#>/biggrin.gif[/img]<!--endemo--> men det där ljudet är klockrent!!! Med metall ljudet och allt...[right][snapback]186689[/snapback][/right]
<!--QuoteEnd--></div><!--QuoteEEnd-->